WiiUBrew

Changes

Hardware/Testpoints (view source)

Revision as of 08:20, 24 March 2025

8,313 bytes added ,  24 March
m
Add TP4004
Line 1: Line 1:  
== General ==
 
== General ==
−
The Wii U motherboard exposes several test points, primarily on the bottom of the motherboard (CPU heatsink facing down).
+
The Wii U motherboard exposes several test points, primarily on the bottom of the motherboard (Opposite side of the SoC).
    
== EXI0 ==
 
== EXI0 ==
−
* TP101 - CLK
+
* TP100 - MOSI (Device in, Wii U out.) (impedance: 40ohm)
−
* TP176 - MISO (Device out, Wii U in)
+
* TP101 - CLK (impedance: 40ohm)
−
* Test point between TP100 and TP176 - MOSI (Device in, Wii U out)
+
* TP102 - CS (impedance: high)
 +
* TP176 - MISO (Device out, Wii U in) (impedance: 476ohm)
    
== DEBUG ==
 
== DEBUG ==
Line 18: Line 19:  
* TP48 - DEBUG6
 
* TP48 - DEBUG6
 
* TP49 - DEBUG7
 
* TP49 - DEBUG7
 +
 +
== SMC ==
 +
* TP15 - Pin 18, 1v adjust
 +
* TP16 - Pin 29, 1v adjust
 +
* TP37 - Pin 27, 1v adjust
 +
* TP38 - Pin 17, 1v adjust
 +
* TP39 - Pin 20, front USB enable
 +
* TP80 - Pin 15, rear USB enable
 +
* TP88/TP152 - Pin 35, Optical power enable
 +
* TP95 - Pin 22, front USB power fault
 +
* TP109 - Pin 16, rear USB fault
 +
* TP144 - SoC nRST, SoC resets when pulled down by a 3.3Kohm resistor.
 +
* TP145 - Connection between RTC and SMC, SMC nRST, sensitive to measurement (power LED reverts to red, but SoC continues running)
 +
* TP171 - Pin 28, Disc present
 +
* TP175 - Connected to RTC and SMC, pulses between 3.3v and 0v at 1Hz
 +
 +
=== I2C ===
 +
* TP153 - SMC SCL
 +
* TP154 - SMC SDA
 +
 +
=== Wireless Modules ===
 +
* TP146 - SMC Pin 1, to RTC, Bluetooth, and 5GHz module. Front LED blinks red when pulled low. BT and 5GHz module reset
 +
* TP155 - SMC Pin 14, WiFi module Pin 14. When pulled low in vWii, system powers off(???)
 +
* TP156 - SMC Pin 23, BT module PON/POFF signal
 +
* TP157 - SMC Pin 19, 5GHz module PON signal
 +
* TP172 - SMC Pin 36, BT module Pin 13. Standby Power-On reset?
 +
* TP173 - SMC Pin 37, WiFi module Pin 7. Standby Power-On reset?
 +
* TP174 - SMC Pin 38, 5GHz module Pin 16. Standby Power-On reset?
 +
 +
=== Faceplate ===
 +
* TP9 - Fake Power Button (active low/pullup, pressed=0.0v, not pressed=3.3v), connected to SMC Pin 33 and RTC. Eject button will also pulse this low.
 +
* TP65/TP2003 - LED_B transistor gate, SMC Pin 39
 +
* TP66/TP2000 - LED_R, SMC Pin 40
 +
* TP67 - LED_W
 +
* TP68 - Not connected to any buttons, connected to SMC Pin 21. When pulled low while powered off, power LED turns orange and eject button is not responsive
 +
* TP70/TP2002 - Power Button, SMC Pin 13 (active low/pullup, pressed=0.0v, not pressed=3.3v)
 +
* TP170 - Eject Button, Pin 35 (active low/pullup, pressed=0.0v, not pressed=3.3v)
 +
* TP2001 - LED_Y, SMC Pin 36
 +
* TP2004 - GND
 +
 +
== Disc Drive ==
 +
* TP2 - Disc drive 3.3V rail
 +
* TP3 - Disc drive 5V rail
 +
* TP4 - Disc drive 12V rail
 +
* TP5 - Disc eject (pulse high for eject)
 +
* TP18 - Disc presence sensor (receiver)
 +
* TP19 - Disc presence sensor (emitter)
 +
* TP76 - Disc inserted (active low)
 +
* TP114 - Disc drive 3.3V always-on rail
 +
 +
== SD Card ==
 +
* TP21 - CLK (Pin5)
 +
* TP22 - CMD (Pin2)
 +
* TP23 - DAT0 (Pin7)
 +
* TP24 - DAT1 (Pin8)
 +
* TP25 - DAT2 (Pin9)
 +
* TP26 - CD/DAT3 (Pin1)
 +
* TP27 - CD1 (Card-Detect signal)
 +
* TP28 - WP2 (Write-Protect signal)
 +
* TP29 - VDD
 +
* TP30 - GND
 +
 +
== Voltage Related ==
 +
* TP31 - Sensor Bar GND PWM
 +
* TP32 - Sensor Bar 12v
 +
* TP73 - RTC Battery 3v3
 +
* TP111 - HDMI 5v supply
 +
* TP115 - 15V DC plug positive
 +
* TP116 - 15V DC plug positive
 +
* TP117 - 15V DC plug negative (0V)
 +
* TP118 - 15V DC plug negative (0V)
 +
* TP120 - 15V power rail B
 +
* TP122 - Always-on 3v3 power rail
 +
* TP123 - 1.5v power rail B
 +
* TP125 - ARM/IOP PGOOD
 +
* TP126 - ARM/IOP LV5065 TD1/TD2?
 +
* TP127 - ARM/IOP/GPU power rail, 1.0v
 +
* TP128 - ARM/IOP/GPU power rail GND
 +
* TP129 - PPC power rail, 1.15v
 +
* TP130 - PPC power rail GND
 +
* TP132 - 3v3/12v PGOOD
 +
* TP135 - 5v power rail A
 +
* TP136 - 12v power rail
 +
* TP137 - 3v3 power rail B ref GND
 +
* TP138 - 3v3 power rail B
 +
* TP139 - WiFi module 3v3
 +
* TP141 - Connected to RTC. WiFi module 3v3 enable.
 +
* TP142 - 3v3 power rail for HDMI Encoder
 +
* TP147 - Connected to RTC and pin4 of U1041 (ABLIC). 15v PFET enable.
 +
* TP148 - Connected to RTC and Q1093 gate. Makes its way to U1041 Pin13 (ABLIC). When pulled low by 3.3kohm resistor, front LED blinks red until 15V unplug+replug. Must be pulled up to 3v3 by 10kOhm resistor, otherwise front LED blinks red upon pressing power.
 +
* TP149 - Connected to LV5066 pin2 (EN) and RTC. 1.5v enable.
 +
* TP158 - 1.5v power rail A
 +
* TP160 - GND
 +
* TP161 - GND
 +
* TP162 - 1.5v power rail A ref GND
 +
* TP163 - 12v power rail ref GND
 +
* TP164 - Always-on 3v3 ref GND
 +
* TP165 - 15V power rail B ref GND
 +
* TP166 - 5v power rail A ref GND
 +
* TP166 - 1.5v power rail B ref GND
 +
* TP168 - 3v3 power rail C
 +
* TP169 - 3v3 power rail C ref GND
    
== Misc/Unk ==
 
== Misc/Unk ==
−
* TP9 - Fake Power Button (active low/pullup, pressed=0.0v, not pressed=3.3v), connected to SMC and RTC. Eject button will also pulse this low.
+
* TP1 - wire goes all the way down near RTC? Also connects to SoC.
−
* TP70 - Power Button (active low/pullup, pressed=0.0v, not pressed=3.3v)
+
* TP6 - To video chip and SoC
−
* TP102 - Not EXI0?
+
* TP7 - Fan Pin 3
−
* TP144 - Reset? Or functions like one when pulled down by a 3.3Kohm resistor.
+
* TP8 - U13 pin4
−
* TP145 - Connection between RTC and SMC, weirdly sensitive to measurement (power LED reverts to red, but SoC continues running)
+
* TP10 - HDMI HPD
−
* TP127 - ARM/IOP power rail?
+
* TP11 - Direct to SoC, no other connections. (impedance: 0.6ohm)
−
* TP170 - Eject Button (active low/pullup, pressed=0.0v, not pressed=3.3v)
+
* TP12 - Direct to SoC, no other connections. (impedance: 20ohm, measures: 1V?)
 +
* TP13 - Direct to SoC, no other connections. (impedance: high)
 +
* TP14 - Direct to SoC, no other connections. (impedance: high)
 +
* TP20 - Direct to SoC, no other connections. (impedance: 1Megohm)
 +
* TP33 - Sensor Bar related
 +
* TP34 - DRAM (U2) VREFDQ (0v7)
 +
* TP35 - DRAM (U2) "ZQ"
 +
* TP36 - DRAM (U3) VREFDQ (0v7)
 +
* TP56 - Direct to SoC, no other connections. (impedance: high)
 +
* TP57 - Direct to SoC, no other connections. (impedance: high)
 +
* TP58 - DRAM (U3) "ZQ"
 +
* TP59 - DRAM (U4) "ZQ"
 +
* TP60 - DRAM (U4) VREFDQ (0v7)
 +
* TP61 - DRAM (U5) "ZQ"
 +
* TP62 - DRAM (U5) VREFDQ (0v7)
 +
* TP64 - To U1014 (comparator?) pin12
 +
* TP69 - Direct to SoC, no other connections. On WUP-DEV-X9, it resides near the second drive connector and is connected to the Classic Controller board (with an MCU between it?). Can be used with a Gamecube Controller. (impedance: high, measures: 3.3v)
 +
* TP78 - Fan Pin1
 +
* TP83 - Direct to video chip.
 +
* TP84 - DDC I2C SDA
 +
* TP86 - Direct to SoC, no other connections. Lots of capacitors? Reference voltage? 1.036v
 +
* TP87 - Direct to SoC, no other connections. Lots of capacitors? Reference voltage? 0.753v
 +
* TP99 - Direct to DRH, no other connections.
 +
* TP110 - DDC I2C SCL
 +
* TP151 - Connected to transistor output, goes to SoC
 +
* TP177 - RTC (Top) Pin 7
 +
* TP179 - Direct to DRH, pullup resistor?
 +
* TP187 - LV5064 pin21 (and more?)
 +
* TP191 - Direct to SoC, no other connections. Nearby Espresso JTAG vias.
 +
* TP1000 - Direct to SoC, no other connections. (impedance: 40ohm)
 +
* TP1001 - Direct to SoC, no other connections. (impedance: 40ohm)
 +
* TP1002 - Direct to SoC, no other connections. (impedance: 40ohm)
 +
* TP1003 - Direct to SoC, no other connections. (impedance: 40ohm)
 +
* TP1004 - LV5064 pin10, temp sensing? direct to SoC
 +
* TP1005 - LV5064 pin11, temp sensing? direct to SoC
 +
* TP1006 - LV5064 pin12, temp sensing? direct to SoC
 +
* TP1007 - LV5064 pin13, temp sensing? direct to SoC
 +
* TP1008 - LV5064 pin14, temp sensing? direct to SoC
 +
* TP1010 - LV5064 pin9, temp sensing? direct to SoC
 +
* TP3000 - Only seen on WUP-DEV-X9, near DRAM
 +
* TP3001 - Only seen on WUP-DEV-X9, near DRAM
 +
* TP3002 - Only seen on WUP-DEV-X9, near DRAM
 +
* TP3003 - Only seen on WUP-DEV-X9, near DRAM
 +
* TP3004 - Only seen on WUP-DEV-X9, near DRAM
 +
* TP3005 - Only seen on WUP-DEV-X9, near DRAM
 +
* TP3006 - Only seen on WUP-DEV-X9, near DRAM
 +
* TP3007 - Only seen on WUP-DEV-X9
 +
* TP3008 - Only seen on WUP-DEV-X9
 +
* TP3009 - Only seen on WUP-DEV-X9
 +
* TP3010 - Only seen on WUP-DEV-X9
 +
* TP3011 - Only seen on WUP-DEV-X9
 +
* TP3012 - Only seen on WUP-DEV-X9
 +
* TP3013 - Only seen on WUP-DEV-X9
 +
* TP3020 - Only seen on WUP-DEV-X9, emerges from under left WiFi card.
 +
* TP3021 - Only seen on WUP-DEV-X9, emerges from under left WiFi card.
 +
* TP3022 - Only seen on WUP-DEV-X9
 +
* TP4000 - Direct to SoC, no other connections. Not present on WUP-DEV-X9. (impedance: 40ohm, measures: 0v)
 +
* TP4001 - Direct to SoC, no other connections. Not present on WUP-DEV-X9. (impedance: high, measures: 3.3v)
 +
* TP4002 - Direct to SoC, no other connections. Not present on WUP-DEV-X9. (impedance: 40ohm, measures: 0v)
 +
* TP4003 - Direct to SoC, no other connections. Not present on WUP-DEV-X9. (impedance: high, measures: 3.3v)
 +
* TP4004 - ???. Only on WUP-30 and later. By the 2.4GHz WiFi module and goes to pin 2 on the (unpopulated) P15.
 +
 
 +
=== Removed/Dev Testpoints ===
 +
Some testpoints can be seen on the WUP-DEV-X9 and CAT-HDD-X5 daughterboard which fit into numeric gaps in WUP-01's testpoints. There are some discrepancies/overlaps in CAT-HDD-X5 testpoints, however.
 +
 
 +
* TP43 - present on CAT-HDD-X5, EXI_INT
 +
* TP45 - present on CAT-HDD-X5, EXI_CS
 +
* TP47 - present on CAT-HDD-X5, EXI_CLK
 +
* TP48 - present on CAT-HDD-X5, EXI_DO
 +
* TP50 - present on CAT-HDD-X5, EXI_DI
 +
* TP53 - present on CAT-HDD-X5, no label
 +
* TP55 - present on CAT-HDD-X5, no label
 +
* TP57 - present on CAT-HDD-X5, no label
 +
* TP58 - present on CAT-HDD-X5, V_IN
 +
* TP62 - present on CAT-HDD-X5, V_5.0
 +
* TP68 - present on CAT-HDD-X5, V_1.2
 +
* TP72 - present on CAT-HDD-X5, V_2.5
 +
* TP74 - present on CAT-HDD-X5, V_3.3
 +
* TP1001 - present on CAT-HDD-X5, SEL_CS
 +
* TP1002 - present on CAT-HDD-X5, SEL_WP
 +
* TP1003 - present on CAT-HDD-X5, SDIO_D3
 +
* TP1004 - present on CAT-HDD-X5, SDIO_D2
 +
* TP1005 - present on CAT-HDD-X5, SDIO_D1
 +
* TP1006 - present on CAT-HDD-X5, SDIO_D0
 +
* TP1007 - present on CAT-HDD-X5, SDIOCMD
 +
* TP1008 - present on CAT-HDD-X5, SDIOCLK
 +
* TP1009 - present on CAT-HDD-X5, POWER_SW
 +
* TP1010 - present on CAT-HDD-X5, FPOFF_SRQ
 +
* TP1011 - present on CAT-HDD-X5, DCDC_OFF
 +
* TP1012 - present on CAT-HDD-X5, VDD_RSTOUT
 +
* TP1013 - present on CAT-HDD-X5, VDD1
 +
* TP1014 - present on CAT-HDD-X5, VDD2
Lazr
31

edits

Retrieved from "https://wiiubrew.org/wiki/Special:MobileDiff/3548...4141"