Hardware/Testpoints
< Hardware
Jump to navigation
Jump to search
General
The Wii U motherboard exposes several test points, primarily on the bottom of the motherboard (CPU heatsink facing down).
EXI0
- TP101 - CLK
- TP102 - CS
- TP176 - MISO (Device out, Wii U in)
- Test point between TP100 and TP176 - MOSI (Device in, Wii U out)
DEBUG
These pins are set to various 8-bit values to indicate the current stage of boot0.
- TP50 - DEBUG0
- TP51 - DEBUG1
- TP52 - DEBUG2
- TP53 - DEBUG3
- TP55 - DEBUG4
- TP54 - DEBUG5
- TP48 - DEBUG6
- TP49 - DEBUG7
Misc/Unk
- TP6 - To video chip and SoC
- TP8 - U13 pin4
- TP9 - Fake Power Button (active low/pullup, pressed=0.0v, not pressed=3.3v), connected to SMC and RTC. Eject button will also pulse this low.
- TP10 - To video chip (and elsewhere?)
- TP11 - Direct to SoC, no other connections.
- TP12 - Direct to SoC, no other connections.
- TP13 - Direct to SoC, no other connections.
- TP14 - Direct to SoC, no other connections.
- TP20 - Direct to SoC, no other connections.
- TP31 - Composite related?
- TP32 - Composite related?
- TP33 - Composite related?
- TP56 - Direct to SoC, no other connections.
- TP57 - Direct to SoC, no other connections.
- TP64 - To U1014 (comparator?) pin12
- TP65 - TP2003
- TP66 - TP2000
- TP67 - to front faceplate
- TP68 - to front faceplate
- TP69 - Direct to SoC, no other connections.
- TP70 - TP2002
- TP83 - Direct to video chip.
- TP84 - To HDMI connector?
- TP86 - Direct to SoC, no other connections. Lots of capacitors? Strap resistor?
- TP87 - Direct to SoC, no other connections. Lots of capacitors? Strap resistor?
- TP109 - USB?
- TP110 - Wire goes past video chip away from SoC.
- TP111 - To HDMI connector?
- TP115 - 12V DC plug positive?
- TP116 - 12V DC plug positive?
- TP117 - 12V DC plug negative?
- TP118 - 12V DC plug negative?
- TP127 - ARM/IOP power rail?
- TP141 - Connected to RTC. Pulled up by Q1080?
- TP144 - Reset? Or functions like one when pulled down by a 3.3Kohm resistor.
- TP145 - Connection between RTC and SMC, weirdly sensitive to measurement (power LED reverts to red, but SoC continues running)
- TP147 - Connected to RTC and pin4 of U1041 (Comparator in?)
- TP148 - Connected to RTC and Q1093 gate. Makes its way to U1041 Pin13 (Comparator ?)
- TP149 - Connected to LV5066 pin2 (EN) and RTC. Regulators enable? Pulldown resistor?
- TP151 - Connected to transistor output, goes to SoC
- TP170 - Eject Button (active low/pullup, pressed=0.0v, not pressed=3.3v)
- TP191 - Direct to SoC, no other connections.
- TP1000 - Direct to SoC, no other connections.
- TP1001 - Direct to SoC, no other connections.
- TP1002 - Direct to SoC, no other connections.
- TP1003 - Direct to SoC, no other connections.
- TP1004 - LV5064 pin10, temp sensing? direct to SoC
- TP1005 - LV5064 pin11, temp sensing? direct to SoC
- TP1006 - LV5064 pin12, temp sensing? direct to SoC
- TP1007 - LV5064 pin13, temp sensing? direct to SoC
- TP1008 - LV5064 pin14, temp sensing? direct to SoC
- TP1010 - LV5064 pin9, temp sensing? direct to SoC
- TP2000 - To SMC
- TP2001 - To faceplate
- TP2002 - Power Button (active low/pullup, pressed=0.0v, not pressed=3.3v)
- TP2003 - To some transistor gate?
- TP2004 - GND